View M170EG01V9_4529281.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M170EG01 V.9
Product Specification
AU OPTRONICS CORPORATION
Product Specification
17.0" SXGA Color TFT-LCD Module
Model Name:
M170EG01 V.9
Approved by
Prepared by
CC Chiu
DDBU Marketing Division / AU Optronics corporation Customer Checked & Approved by
ver0.1
1/25
M170EG01 V.9
Product Specification
Product Specification
17.0" SXGA Color TFT-LCD Module Model Name: M170EG01 V.9
(u) Preliminary Specifications ( ) Final Specifications
Note: This Specification is subject to change without notice.
ver0.1
3/25
M170EG01 V.9
Product Specification
Contents
1.0 Handling Precautions.........................................................6 2.0 General Description ...........................................................7
2.1 Display Characteristics.................................................................................................................... 7 2.2 Optical Characteristics..................................................................................................................... 8
3.0 Functional Block Diagram ................................................11 4.0 Absolute Maximum Ratings..............................................12
4.1 TFT LCD Module ............................................................................................................................ 12 4.2 Backlight Unit .................................................................................................................................. 12 4.3 Absolute Ratings of Environment .................................................................................................. 12
5.0 Electrical characteristics ..................................................13
5.1 TFT LCD Module ............................................................................................................................ 13
5.1.1 Power Specification..........................................................................................................................13 5.1.2 Signal Electrical Characteristics........................................................................................................14
5.2 Backlight Unit .................................................................................................................................. 15
6.0 Signal Characteristic........................................................15
6.1 Pixel Format Image ........................................................................................................................ 15 6.2 The input data format...................................................................................................................... 16 6.3 Signal Description.......................................................................................................................... 17 6.4 Interface Timing ............................................................................................................................... 18
6.4.1 Timing Characteristics......................................................................................................................18 6.4.2 Timing diagram ................................................................................................................................19
6.5 Power ON/OFF Sequence ............................................................................................................ 20
7.0 Connector & Pin Assignment............................................21
7.1 TFT LCD Module ............................................................................................................................ 21 7.2 Backlight Unit .................................................................................................................................. 22 7.3 Signal for Lamp connector............................................................................................................. 22
8.0 Reliability ........................................................................23 9.0 Safety ..............................................................................24
9.1 Sharp Edge Requirements............................................................................................................ 24 9.2 Materials .......................................................................................................................................... 24
9.2.1 Toxicity...........................................................................................................................................24 9.2.2 Flammability....................................................................................................................................24
9.3 Capacitors....................................................................................................................................... 24
10.0 Other requirement .........................................................24
10.1 National Test Lab Requirement................................................................................................... 24 10.2 Label.............................................................................................................................................. 24
11.0 Mechanical Characteristics.............................................25
ver0.1 4/25
M170EG01 V.9
Product Specification
Record of Revision
Version and Date Page 0.1 2005/02/28 All Old description First Edition for Customer New Description Remark
ver0.1
5/25
M170EG01 V.9
Product Specification
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press or pat the panel surface by fingers,hand or tooling. 9) Do not press the reflector sheet at the back of the module to any directions. 10) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged.
ver0.1
6/25
M170EG01 V.9
Product Specification
2.0 General Description
This specification applies to the 17.0 inch Color TFT/LCD Module M170EG01 V9. This module is designed for a display unit of personal computer. The display supports the SXGA (1280(H) x 1024(V)) screen format and 16.2M colors (RGB 6-bits + FRC data). All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 J condition: ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance Contrast Ratio Optical Rise Time/Fall Time Color Saturation Nominal Input Voltage VDD Power Consumption (VDD line + CCFL line) Weight Physical Size Unit [mm] [mm] [mm] SPECIFICATIONS 432(17.0") 337.920 (H) x 270.336(V) 1280(x3) x 1024 0.264 (per one triad) x 0.264 R.G.B. Vertical Stripe Normally White 420 (Typ) 500 : 1 (Typ) 8 (Typ) 72% NTSC +5.0 V 25.8 W(Typ) (PDD=6 W, PCFL=19.8 W @Lamp=7.5mA) 1900 (Typ) Min. Typ. Horizatal(H) 358 358.5 Vertical(V) 296 296.5 Depth(D) 16.5 17.0 Dual Channel LVDS 16.2M colors (RGB 6-bit + FRC data) 0 to +50 -20 to +60 Hard-coating (2H), Glare treatment
[cd/m2] [msec] [Volt] [Watt] [Grams] [mm]
(Note 1)
Max. 359.0 297 17.5
Electrical Interface Support Color Temperature Range Operating Storage (Shipping) Surface Treatment
[oC] [oC]
Note 1 :System should be warmed up for at least one hour
ver0.1
7/25
M170EG01 V.9
Product Specification 2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25J (Room Temperature): Item Unit Conditions Min. Typ. Max. Horizontal (Right) 60 70 CR = 10 (Left) 60 70 Vertical (Up) 60 70 CR = 10 (Down) 50 60 Viewing Angle [degree] Horizontal (Right) 70 80 CR = 5 (Left) 70 80 Vertical (Up) 70 80 CR = 5 (Down) 70 80 Contrast ratio Normal Direction Rising Time Response Time [msec] Falling Time Rising + Falling Red x Red y Color / Chromaticity Coordinates (CIE) Green x Green y Blue x Blue y Color White White Luminance @ CCFL 7.5mA (center) Luminance Uniformity Crosstalk (in 75Hz) Flicker Equipment [cd/m ] [%] [%] dB Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter
2
Note -
300 0.61 0.31 0.26 0.58 0.11 0.04 0.28 0.30 336 75
500 6 2 8 0.64 0.34 0.29 0.61 0.14 0.07 0.31 0.33 420 80 1.5 -20 9 4 13 0.67 0.37 0.32 0.64 0.17 0.10 0.34 0.36
-
Note 1
Coordinates
(CIE)
White x White y
Note 2 Note 3 Note 4
(PR 880, BM-5A / BM7, CS-1000, CA210, SR_3, EZ Contrast*, Optiscope& Westar TRD-100) Aperture Test Point Environment 1Xwith 100cm VD or 2Xwith 50cm viewing distance Center (VESA point 9) < 1 lux
Module Driving Equipment
*' EZ Contrast is different measurement tool with very close viewing distance.
LCD Module
measuring distance
PR-880 / BM5A / BM7
ver0.1
8/25
M170EG01 V.9
Product Specification
Note 1: Definition of Response time The output signals of photodetector are measured when the input signals are changed from " Full Black" to " Full White" (rising time), and from " Full White" to " Full Black "(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes.
%
Tr F
Tr R
100 90 Optical response 10 0 White Black White
Note 2: Brightness uniformity of these 9 points is defined as below 90 %
50 %
10 % 10 %
50 %
90 %
Uniformity =
Minimum Luminance in 9 points (1 - 9) Maximum Luminance in 9 Points (1 - 9)
ver0.1
9/25
M170EG01 V.9
Product Specification
Note 3: Crosstalk is defined as below : 1/2 1/6 1/6 2/3 1/2 1/3 1/6
A
A'
1/6 1/3 1/2 B' 2/3
1/2 B 184 gray level 184 gray level
Unit: percentage of dimension of display area
0 gray level
l LA-LA' l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B l LB-LB' l / LB x 100%= 1.5% max., LA' and LB' are brightness at location A' and B'
Note 4: Test Paterm: Subchecker Pattern
RGBR GB Gray Level = L127 RGBR GB Gray Level = L0
RGBR GB
Method: Record dBV & DC value with (WESTAR)TRD-100 Amplitude
AC
DC Time
Flicker (dB) = 20 log
AC Level(at 30 Hz) DC Level
ver0.1
10/25
M170EG01 V.9
Product Specification
3.0 Functional Block Diagram
The following diagram shows the functional block of the 19.0 inches wide Color TFT/LCD Module:
AU ASIC
Timing Controller
G1
Y-Driver IC
LVDS
LVDS Receiver RSDS Transmitterr
TFT-LCD 1280*(3)*1024 Pixels
X-Driver IC
Connector
+ 5V
G1024 D1
D3840 4 CCFL
DC/DC Converter
Gamma Correction
DC POWER
Inverter
AL2307-A0G1D-P / FI-XB30SSRL-HF16 Mating Type: JAE FI-X30HL
JST-BHSR-02VS-1 ( 2pin N2 ) SM02B-BHSS-1-TB
ver0.1
11/25
M170EG01 V.9
Product Specification
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 TFT LCD Module
Item Logic/LCD Drive Voltage Symbol VIN Min -0.3 Max +6 Unit [Volt] Conditions Note 1,2
4.2 Backlight Unit
Item CCFL Current Symbol ICFL Min Max 8.5 Unit [mA] rms Conditions Note 1,2
4.3 Absolute Ratings of Environment
Item Operating Temperature Operating Humidity Storage Temperature Storage Humidity Symbol TOP HOP TST HST Min 0 5 -20 5 Max +50 90 +60 90 Unit [ C] [%RH] [ C] [%RH]
o o
Conditions Note 3 Note 3 Note 3 Note 3
Please refer the graph below for corresponding of Min/Max values of temperature and humidity. Note 1: With in Ta (25J ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard).
ver0.1
12/25
M170EG01 V.9
Product Specification
5.0 Electrical characteristics
5.1 TFT LCD Module 5.1.1 Power Specification
Input power specifications are as follows; Symbol VDD IDD Irush PDD VDDrp Parameter Logic/LCD Drive Voltage VDD current LCD Inrush Current VDD Power Allowable Logic/LCD Drive Ripple Voltage Min 4.5 Typ 5 1200 6 Max 5.5 1560 2.5 7.8 100 Units [Volt] [mA] [A] [Watt] [mV] p-p 10% Vin=5V , All Black Pattern, at 75Hz Note Vin=5V , All Black Pattern, at 75Hz Vin=5V , All Black Pattern, at 75Hz Condition
Note: Measurement conditions:
+5.0V D6 D5 D2 D1 R1 47K
Q3 AO6402 F1 S VCC
G
(LCD Module Input)
C1 1uF/16V
(High to Low) Control Signal
SW
D1 D2 D5 D6 R2 G 1K C3 +12.0V VR1 47K 0.01uF/25V S Q3 AO6402 C2 1uF/25V
90%
5.0V
10% 0V 470 us
Vin rising time
ver0.1
13/25
M170EG01 V.9
Product Specification 5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows; Symbol VTH VTL | VID| VICM Parameter Differential Input High Threshold Differential Input Low Threshold Input Differential Voltage Differential Input Common Mode Voltage Min -100 100 1.1 Typ 400 Max 100 600 1.45 Units [mV] [mV] [mV] [V] VTH/VTL = O100mV Condition VICM = 1.2V VICM = 1.2V Note Note Note Note
Note: LVDS Signal Waveform
VTH xVIDx VTL
VICM
VSS
ver0.1
14/25
M170EG01 V.9
Product Specification
5.2 Backlight Unit
Parameter guideline for CCFL Inverter Symbol ISCFL Parameter CCFL standard current Min. 7.0 Typ. 7.5 Max. 8.0 Unit [mA] rms IRCFL FCFL ViCFL (0 C) ViCF (25 C) VCFL (for reference) CCFL Power consumption PCFL (for reference) LTCFL CCFL life Time 30,000 50,000 Note 1: CCFL standard current is measured at 25O J. 2 [Hour] (Ta=25oC) Note 4 19.8 21.8 [Watt]
o o
Condition (Ta=25oC) Note 1
CCFL operation range CCFL Frequency CCFL Ignition Voltage
3.0 40
7.5 60
8.0 80
[mA] rms [KHz] [Volt]
(Ta=25oC) (Ta=25oC) Note 2 (Ta=0oC)
1500 (End of the lamp wire connector) CCFL Ignition Voltage 1150 (End of the lamp wire connector) CCFL Operation Voltage -
-
rms [Volt]
660 @7.5mA
rms 700 @3.0mA [Volt] rms
(Ta=25oC)
(Ta=25oC) Note 1
(Ta=25oC) Note 3
Note 2: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 3: The variance of CCFL power consumption is 10%. Calculator value for reference (ICFLxVCFLx 4=PCFL). Note 4: CCFL life time is determined as the time at which brightness of lamp is 50%. The typical life time of CCFL is on the condition at 7.5 mA lamp current.
6.0 Signal Characteristic
6.1 Pixel Format Image
ver0.1 15/25
M170EG01 V.9
Product Specification
Following figure shows the relationship of the input signals and LCD pixel format.
ODD 1 ST
EVEN
ODD
EVEN
ODD
EVEN
RGBRGBRGB
RGBRGBRGB
1024 TH
RGBRGBRGB
RGBRGBRGB
6.2 The input data format
Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: Please follow PSWG. Note3: 8-bit in
ver0.1
16/25
M170EG01 V.9
Product Specification 6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RxOIN0RxOIN0+ RxOIN1RxOIN1+ RxOIN2RxOIN2+ VSS RxOCLKINRxOCLKIN+ RxOIN3RxOIN3+ RxEIN0RxEIN0+ VSS RxEIN1RxEIN1+ VSS RxEIN2RxEIN2+ RxECLKINRxECLKIN+ RxEIN3RxEIN3+ VSS VSS NC VSS VCC VCC VCC DESCRIPTION Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) Power Ground Negative LVDS differential clock input (Odd clock) Positive LVDS differential clock input (Odd clock) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Positive LVDS differential data input (Even data) Negative LVDS differential data input (Even data) Power Ground Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Negative LVDS differential clock input (Even clock) Positive LVDS differential clock input (Even clock) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Power Ground No Connection ( for AUO test) Power Ground +5.0V Power Supply +5.0V Power Supply +5.0V Power Supply
ver0.1
17/25
M170EG01 V.9
Product Specification
Note1: Start from left side
Connector
1 RxOIN0Note3: Please follow PSWG.
30 VCC
Note2: Input signals of odd and even clock shall be the same timing.
6.4 Interface Timing 6.4.1 Timing Characteristics
Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Item Data CLK H-section V-section Period Display Area Period Display Area Symbol Tclk Th Tdisp(h) Tv Tdisp(v) F Min 40 685 640 1036 1024 49 Typ 54 844 640 1066 1024 60 Max 70 1024 640 2048 1024 76 Unit MHz Tclk Tclk Th Th Hz
Frame Rate Note : DE mode only
ver0.1
18/25
M170EG01 V.9
Product Specification 6.4.2 Timing diagram
DE
CLK DE
Tclk
Tblk(v)
Th
Tv
Tdisp(h) Th
Tdisp(v)
Tblk(h)
ver0.1
19/25
M170EG01 V.9
Product Specification
6.5 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off.
90%
90%
Vin 0V
10%
10%
10%
T1 Signal 0V
T2
T5
T6
T7
T3
T4
Lamp 0V
Symbol T1 T2 T3 T4 T5 T6 T7
Min. 0.5 0 200 100 0 1000
Values Typ. 16 -
Max. 10 10 50 10 -
Unit ms ms ms ms ms ms ms
Note: The values of the table are follow PSWG.
ver0.1
20/25
M170EG01 V.9
Product Specification 7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation Manufacturer Type Part Number Mating Housing Part Number Pin# 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal Name RxOIN0RxOIN1RxOIN2VSS RxOCLKIN+ RxOIN3+ RxEIN0+ RxEIN1VSS RxEIN2+ RxECLKIN+ RxEIN3+ VSS VSS VCC Interface Connector / Interface card JAE or compatible AL2307-A0G1D-P / FI-XB30SSRL-HF16 JAE FI-X30HL Pin# 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal Name RxOIN0+ RxOIN1+ RxOIN2+ RxOCLKINRxOIN3RxEIN0VSS RxEIN1+ RxEIN2RxECLKINRxEIN3VSS NC VCC VCC
ver0.1
21/25
M170EG01 V.9
Product Specification
7.2 Backlight Unit
Connector Name / Designation Manufacturer Type Part Number Mating Type Part Number Lamp Connector / Backlight lamp JST BHSR-02VS-1 SM02B-BHSS-1-TB
7.3 Signal for Lamp connector
Connector No. CN1 Upper CN2 Pin No. 1 2 1 2 1 2 1 2 Input Hot1 Cold1 Hot2 Cold2 Hot1 Cold1 Hot2 Cold2 Color Pink White Blue Black Pink White Blue Black Function High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage
CN3 Lower CN4
ver0.1
22/25
M170EG01 V.9
Product Specification
8.0 Reliability
Reliability test condition
No Test Item 1 2 3 4 5 6 7 8 9 Temperature Humidity Bias (THB) High Temperature Operation (HTO) Low Temperature Operation (LTO) High Temperature Storage (HTS) Low Temperature Storage (LTS) Thermal Shock Test (TST) On/Off Test Shock Test (Non-Operating) Vibration Test (Non-Operating) Test Condition 50J, 80%, 300hours 50J, 300hours 0J, 300hours 60J, 300hours -20J, 300hours -20J/30min, 60J/30min, 100 cycles On/10sec, Off/10sec, 30,000 cycles 50G, 20ms, Half-sine wave (+ X, +Y, +Z) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z) Contact Discharge: 8KV, 150pF(330O ) 1sec, 8 points, 25 times/ point Air Discharge: 15KV, 150pF(330O ) 1sec, 8 points, 25 times/ point 11 Altitude Test Operation:10,000 ft Non-Operation:30,000 ft 12 Drop Test The drop height is 60cm
10 ESD (ElectroStatic Discharge)
ver0.1
23/25
M170EG01 V.9
Product Specification
9.0 Safety
9.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
9.2 Materials 9.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist.
9.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.
9.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
10.0 Other requirement
10.1 National Test Lab Requirement
The display module will satisfy all requirements for compliance to UL 1950, First Edition CSA C22.2 No.950-M89 EEC 950 EN 60 950 U.S.A. Information Technology Equipment Canada, Information Technology Equipment International, Information Technology Equipment International, Information Processing Equipment (European Norm for IEC950)
10.2 Label
The label is on the panel as shown below:
ver0.1
24/25
11.0 Mechanical Characteristics
Ver0.2
25/24
Ver0.2
26/25

▲Up To Search▲

Price & Availability of M170EG01V9

	To Download M170EG01V9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .